DIY: Setting up wireless access points as repeaters to extend wireless range

Configuration Suggestions

Quick overview
Is this faq useful? A very useful answer, thank you. Areas with poor signal strength should be hard-wired to the hub; areas with very poor or no signal strength should be covered by the wireless repeater. Each access point must have a unique name, called an "SSID" -- the repeater uses it to find the access point. Activate Alert Search Archives. Enlightenment Has Limits in Bodhi Linux.

Re: Multiple APs should use different channels but the same SSID?

How to Boost Your Home WiFi With Multiple Repeaters and Access Points

Business Wireless Takes your enterprise Wi-Fi to new levels. Support Where to Buy. User Application Requirement Updated This Article Applies to: Some wireless bridges support only a single point-to-point connection to another AP. Others support point-to-multipoint connections to several other APs.

This article is about to setup a Point to Multi-Point Bridge. If you cannot log into the Web-based Interface, please click here and follow the instruction for a try.

After changing the IP address of your access point, you need to re-log into it by using the new IP address. And please note that the IP addresses of the access points cannot be the same in your network.

Press Survey or Search button and an AP list will be displayed. The repeater extends the star outwards and extends the range outwards from the existing router. The existing router feeds an access point via a cable, and then the access point feeds the repeater, which in turn feeds the end user device. Rooms that have a satisfactory signal obtained in the initial survey can be ignored. Areas with poor signal strength should be hard-wired to the hub; areas with very poor or no signal strength should be covered by the wireless repeater.

For example, if the existing router is in the den on one side of the house and there's very poor signal in the kitchen on the other side of the house, then place a wired access point in the hallway outside the den, and a wireless repeater in the kitchen. The cabled wireless access point will function like a shifted existing router, extending the wireless signal down the hallway. The wireless repeater will pick the signal up and distribute it to low-power devices in the kitchen.

You can use any existing WiFi routers. Then save the configuration. Use an unintuitive LAN Ethernet port on the new router -- the one that's converted to an access point -- and not the WAN port when connecting to the existing router. Follow the product-included instructions to configure each repeater to repeat each access point, or the existing WiFi-enabled router. Each access point must have a unique name, called an "SSID" -- the repeater uses it to find the access point.

At a family member's home recently, I hard-wired one access point to the existing router and then placed that access point in the living room. I then placed one of the wireless repeaters, configured to repeat the living room access point, in the previously-no-signal yard, thus providing signal outside. I placed a second wireless repeater, configured to repeat the existing WiFi-enabled router, in an upstairs bedroom that had good signal coverage from the existing survey. This provided good repeated signal in a bedroom down the upstairs hallway that had very poor signal strength initially.

Is there a piece of tech you'd like to know how to operate properly? Is there a gadget that's got you confounded? Please send your tech questions to me , and I'll try to answer as many as possible in this column. And use the Talkback feature below to add your comments!

Patrick Nelson has been a professional writer since He was editor and publisher of the music industry trade publication Producer Report and has written for a number of technology blogs.

Nelson studied design at Hornsey Art School and wrote the cult-classic novel Sprawlism. His introduction to technology was as a nomadic talent scout in the eighties, where regular scrabbling around under hotel room beds was necessary to connect modems with alligator clips to hotel telephone wiring to get a fax out. He tasted down and dirty technology, and never looked back. September 19, Get Permission to License or Reproduce this Article. Be the first to comment!

More in How To. Top 5 iOS Utilities and Tools. Most Popular Newsletters News Alerts. What do you think of commercial spaceflight? It's the best hope for advancing space exploration. It's little more than a hobby for billionaires. It will result in highly profitable new industries, like space mining. It will dramatically increase space junk and pollution.

It will offer the opportunity to establish a new way of life in space colonies. It should be heavily regulated by governments. Vote to See Results. Salesforce Philanthropy Cloud at Dreamforce.

Step 1: Survey

Looking to set up network in new home with multiple access points solved Setting up Wireless access points with router, guest network, portal ID page, security concerns; Need Specific Guidance on Setting Up My Home Wired & Wireless Network; Setting up a wired/wireless network at home. The process of developing a wireless network becomes complex when you are deploying multiple APs throughout a multi-story building, because in addition to your neighbors Access Points (APs) you need to worry about location, channel selection, and interference from your old APs with each other. Creating one WiFi network with multiple access points. I picked up an old Dlink DIR router and began configuring it. The first thing I did was disabling DHCP and NAT on the router (bridged). and set them to use the same password. Once configured, devices connected to our WiFi network will automatically switch between routers when.